Lodar 2 Function TI Mini RX with Master + TI Standard Tr Manuel d'utilisateur télécharger pdf

11102RX.01E

Wiring Instructions for 11 Series 2 Function Receivers

or Disconnect Battery

IDENTIFY POWER

CONNECTION POINT

AND ISOLATE SUPPLY

Fuse

Remove fuse

Vehicle batteries contain gasses

which are flammable and explosive.

Wear eye protection and do not lean

over battery while disconnecting. Do

not wear metal jewellery.

WARNING

BEFORE YOU START

A1102 RX

& A1102E RX

have

7 core cable

A1100 RX

has 4 core

cable

Secure using 5mm (3/16") bolts (not supplied)

through the 2 mounting feet

CAUTION

MOUNT RECEIVER

STOP

POSITIVE

NEGATIVE

TAKE TIME TO LOCATE THE BEST POSITION

If necessary, power the Receiver and move it around

the vehicle until the required performance is achieved.

Operate the Transmitter and observe the Receiver

internal LED’s.

Mount as HIGH as possible

AVOID surfaces with HEAVY VIBRATION

AVOID DIRECT SPRAY from wheels

In a HOT CLIMATE fit in a SHADED position

Cable gland should face DOWN or BACK

Receiver 90 and 91 Series (Black lid)

Waterproof to IP67 complete with 1.5 metres (5ft) cable

1. The Receiver is designed to carry a maximum of 8 Amps, with an individual output maximum

of 5 Amps. If you need to switch higher currents, then the you should consider the 92 or the

93 series which can switch up to 15 Amps.

2. Master Output. This can be configured to Continuous or Parallel operation, see overleaf for

details. (This feature is not available on 90 1 00 and 91 1 00 models)

3. Receiver outputs, when connected in parallel with an external switching device (wired

remote), will instantly switch off if the wired remote is operated. This is a feature of the

safety circuits.

4. Lodar Receivers have an isolation switch for safety and to allow for registering a MUST

replacement Transmitter.

5. Safety Feature. Both the Transmitter and the Receiver will switch off after 30 minutes of

inactivity. Other Timeouts are available, ask your dealer.

CONNECT

WIRES

Transmitter

Function

Convention

F1 F2

or re-connect Battery

ACTIVATE THE

RECEIVER SUPPLY

Fuse

Replace fuse

Press the Transmitter buttonRESET

to activate the system, and carefully

test each function for correct operation.

TEST

CONNECT TRANSMITTER BATTERY

Batteries generally have to be

disconnected when shipping.

12/24 Volts DC Nominal

Positive Supply

RED

BLACK

GREEN

YELLOW

BROWN

WHITE

Master

Wire Colour

Not Present

Not Used

Make notes about the

connections made

in the boxes below

What is the MASTER Output for ?

It is used to operate the pump of an electro-hydraulic

power pack or maybe a clutch pump. It can also be

used for powering a dump valve, master valve etc.

It can be configured to work continuously, that is ON

when SET is pressed and OFF when STOP is

pressed; or in parallel with any output, that is, it is

active only a function is operated. If it is needed with

certain functions only, this can easily be configured.

Wire used for

Zero Volts (Ground)

Output Function 1

Output Function 2

Secondary Master

BLUE

E-Stop Loop

BROWN

Not Present

Option

11 100

11 102 11 102E

lodar.com

Option

1 2

11 102 11 102E 1
9004RX.01E 2

Résumé du contenu

Page 1 - 11 102 11 102E

11102RX.01EWiring Instructions for 11 Series 2 Function Receivers2or Disconnect BatteryIDENTIFY POWERCONNECTION POINTAND ISOLATE SUPPLYFuseRemove fuse

Page 2 - 9004RX.01E

9004RX.01EContact Information:Lodar Limited,60 Sandwell Street,Walsall. WS1 3EB. UKTel. +44 1922 613633Fax. +44 1922 626991www.lodar.comLED marked “P

Commentaires sur ces manuels

Pas de commentaire

Lodar 2 Function TI Mini RX with Master + TI Standard Tr Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Récepteurs et amplificateurs Lodar 2 Function TI Mini RX with Master + TI Standard Tr. Lodar 2 Function TI Mini RX with Master + TI Standard Transmitter User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Récepteurs et amplificateurs Lodar 2 Function TI Mini RX with Master + TI Standard Tr